PRODUCT DESCRIPTION
Keeping safety for the user, your customers
and the environment in mind, EFC-38 was developed to tackle your tough wood
deck restoration projects fast. This unique formulation provides the strength
necessary to strip most semi-transparent stains and sealers, dead, gray wood,
mold, mildew and heavy accumulations of grime.
EFC-38 is a highly developed dry powder
formulation that mixes easily with water. Mixing your own solution allows you
greater flexibility as well as tremendous savings. Even when mixed at full
strength, EFC-38 is less than 1/6 the cost of any comparable liquid
formulation. Unlike other per carbonate based cleaners, EFC-38 utilizes a
proprietary blend of specialized ingredients which controls pH allowing you to
melt off existing finishes without the need for excessive masking.
EFC-38 is safe for use around pets and
plants!
AVAILABILITY
EFC-38 is available in 10lb and 30lb
contractor tubs. EFC-38 is also available in 450# bulk drums.
DILUTION
The standard mix rate at full strength is
1/2lb per gallon of water.
RECOMMENDATIONS
Try EFC-38 as a general purpose cleaner for
vinyl siding, lawn furniture and sidewalks.
For even more dramatic results, follow EFC-38 with Citralic
Brightener/Neutralizer on your next wood restoration project.
PRODUCT USAGE
For best results always use EFC-38 as
instructed by the product label. Always perform a test patch to determine
product suitability. EFC-38 is designed for use on all exterior wood.
First apply EFC-38 to a small inconspicuous
area of about one square foot. Choose a spot on the deck, fence or siding that
is well protected from the elements such as behind a bush or under a planter or
mat on a deck. The idea is to choose an area that will present the greatest
challenge.
After you have applied the EFC-38 to the test
patch, allow to dwell 5 - 10 minutes and perform a scratch test. Using a tongue
depressor (or a stick), scratch with light pressure back and forth over the
treated surface. If the surface can easily be removed showing bare wood stop
the test and note the dwell time. If the surface resists the scratch test, allow
an additional 5 minutes of dwell time keeping the surface wet with EFC-38 and
perform another scratch test. When you are able to easily remove the finish
with a scratching motion, note the total dwell time and rinse the surface
thoroughly.
Depending on the age, type and condition of
the finish you are removing, the dwell time can be anywhere from 5 - 15
minutes. The dwell time may be longer if there are multiple coats of finish
that need to be removed.
PRODUCT APPLICATION
When applying EFC-38 be sure to take
necessary masking precautions. Protect all adjacent surfaces that are not to be
stripped. Protect vegetation from direct overspray. EFC-38 should not cause
spotting on most plants. If plants do spot, this will only affect existing
foliage. New growth will not be effected.
Apply product from bottom to top being
careful to saturate the entire surface you intend to clean. When working on
large areas, keep the product wet for the duration of the dwell time. If the
product dries, it has quit working. For best results keep wet with a mist of
EFC-38.
When cleaning a cedar home or log cabin treat
the bottom three courses of an entire wall then work back treating the next
three courses. Continue in this manner until you have reached the top of the
wall. Keep the surface wet with an additional misting of EFC-38 as necessary.
FINISH REMOVAL
Perform a scratch test on the finish being
sure to pick a spot that would likely be the toughest to remove. If the surface
can easily be scratched off revealing bare wood beneath, you are ready to rinse.
If the surface is not easily removed, allow additional dwell time keeping the
surface wet.
When you are ready to rinse the surface, use
a pressure washer at the lowest possible pressure. 600 - 900 PSI is ideal. Work
following the same pattern you used when applying the EFC-38. Rinsing should be
done in a sweeping motion, fanning your strokes at the beginning and end. After
you have removed the finish from the entire surface you are working on give the
surface a good rinse.
BRIGHTENING
After rinsing apply Citralic Brightener /
Neutralizer to restore the woods natural color and pH.